BOARDS,fit great, need linkage/TRAILER HITCH, fit,supports needed

[Piute]

   Hey TOOL's will these boards fit real bikes  
   
Think these will ad to comfort ,but worried about spacing for shifter going to check if can spot were they mont(if they will)on my S.S.Real-Bike
                                                     More like A dang x-mas tree

[TOOLS1]

A cutting torch, and a welder, and, you could mount them on anything. They don't look like they are made, for a CB 750. However Triple A floor boards are nice. They did make them, for CB 750's that had the shifter, and break mounted on them. If, you could find a set, for less then $250.00 get them. They are in demand. I have a set, but I need longer spacers to mount them on the Toolmatic. The engine is wider at the left rear.
TOOLS

[Piute]

         

                                                     These are off a 750A
                            Why I was asking never looked at a 750A with boards on .
      If i have to mod brackets ,then may as well make my own out of some fuglys I got ,
      But wont A more Stk.look,since these were on 750 ? maybe better fit .
      So A Auto has A bigger right side,have to check that quick.

[Piute]

                                          Well found what I think I needed

 This complete kit was already sold,but went ahead and got other witch was just the mounts N boards

                                 So either there's a kit or try to get info from pics

                                             Have these one's on the way

Vintage 1977 Honda CB750 CB 750A Hondamatic Part- Triple A Custom Running Boards


 










If can't find kit(forward controls?) I can get the parts cut,Also know of a great welder.

Item condition: Used
 
Sold For: US $40.00  
 
Shipping: $20.00 Standard Shipping See more services  See shipping discounts  

Start of LayerEnd of Layer |  See all shipping details
 Item location: Oceanside, California, United States
 Ships to: United States  
 
Delivery: Estimated within 2-6 business days  
 
Returns: 14 days refund, buyer pays return shipping  
 

[TOOLS1]

Now that is a nice set. Too bad, you could not get it, for $40.00. The Matics, and the K, and F's all have the motor mounts in the same place, so they should bolt right on. It's just wider, and a little higher where the shifter cover is. The bracket that curves up to the top rear mount hits on the corner of that cover. Some 3/4" inch spacers, and I could mount my set, but just don't have time, or ambition. Her are some pictures of Monsterbroncs bike with Triple A running boards.
 

 
TOOLS

[Piute]

  I think the full set went foir 185.00,But the boards and bracket I got coming .
I can make (Pauls help)all that is needed,just will need to be welded by a pro ,not me.
   need extra brake lever and shift lever to mess with(cut and exstend).



  Thanks for picture's more the easyer It is to make less mistakes(trial bends)

[Piute]

   My boards and mounts came today
 there not made like any of the pictures we posted ,these (mine)are made for A 77 So that would be why,cause they seem like there going to line up nice.sure going to have to make levers but expected,NEED EXTRA's if any one has BRAKE lever and SHIFT lever

[shinyribs]

Where do your feet go when you stop? I have a hard enough time clearing my pegs when at a light as is! I could only imagine straddling those floor boards. Dang,they do look cool and comfy,though.

[Piute]

                                        STK. SHIFTER FOR NOW

                NEED A 7"LONG LEVER WITH A 2" OFF SET (AWAY FROM ENG.)

                        TO FRONT EDGE OF BOARD IS 11" FROM SHIFT .

[Piute]

shinyribs wrote

Where do your feet go when you stop? I have a hard enough time clearing my pegs when at a light as is! I could only imagine straddling those floor boards. Dang,they do look cool and comfy,though.

   Well with thoughs cafés
 Your stuck doing your tank  and not much room to move around,your taller so not to bad I'd think,But ya get used to were to put those feet,
                                        Ya had to mention that BUD
    PLENTY OF EXTRA ROOM (had to put on tire )sat on and checked see were seat and tank meet,feet towards the backNo staddling at all

[shinyribs]

Good point.My tank is 3'' longer than stock.I cant sit with my feet in front of the pegs. The pegs hit me right at the ankles.I have to stand with my feet behind the pegs. Darn cafe junk

[Piute]

  Your learning fast ,building H.J.
  Wish I had time to do another ,Naaa Get the Elc.back on the road and sell,need an R.V.
  I don't ride fast,sure I love to move ,But comfort and long runs is my way to play.
    By the way who else has a bagged out 750 .

[bosco39]

I know I have a rear brake pedal if you need one. Let me know if you do need it.

[Piute]

  Yes,.
your not regestard so p.m.me by clicking my name and then I'll get your "E" and send info


 Depending on what ya have ,I'd like to save my stock one and weld tabs on another,
This fit O.K. but not hooked up completly need linkage to spline (longer spline ?)

                                       TANKS

[Piute]

   Most of this is going to be hit N miss ,
  So on lookingfor any idea's decide to add these to the parts ben
B M W 10 bucks off the E.taking a chance may have right bends
<

 YamaHAHA 12 bucks This linkage has potential for both side's maybe( 2 More available)

[TOOLS1]

I have a big break pedal thingy that fits over the stock break pedal. It was on the Toolbagger when I got it. It's yours if, you want it.
TOOLS

[Piute]

  THINGY  IS IT BLK.YOU BET I DO,Havin hard time with shifter lost bid on bmw shifter by .50 ,trying to figure charging prob. think I pinched a wire on dang cover ,hurting for therapy N transpo..
 hate to miss work at 1n1/2 O.T. fer fri. n sat. .going to have 4th of july wk off (basic pay),Ya still have my #s

[TOOLS1]

Somewhere, but shoot them to me again.
TOOLS

[Piute]

 B.M.W. shifter
  Person canceled there bid,I just made offer Exp.shp.and will be here by 20th

  Problem fixed on charging was as thought grounded out by getting pinched,shrink tubes and mo careful putting cover on.Tomorrow to work will be the 1st true run(other then around the home area)can't check much ,speedo not working YET is a 40 mile run ,sure hope the brakes work ,may end up passing  my exit,  and have no revers

                                                 

[shinyribs]

LOL.Dont pass that exit! A few weeks back I was out on the bike and there was NO traffic on the interstate. I rode laps around this one clover leaf for about 15 minutes. Lean-swerve-lean-swerve....it sounds retarded,but it was a blast. I'm so easily amused!