New to the site.... Will need alot of info from all you..

[Piute]

  Some say some of the 1st thing'S' you should change is the plastic sleeve in swing arm and the ball bearings in the neck,I'm on that now ,BUTThere's no slop in the swing at all,just checked ,So thinking of putting on hold till rear tire change
( good riding 2k at the most till then ?).
  Your right I think that the look your wonting you need those spokes,
For pulling a trailer I need a mag in rear and the stock set-up is great.
  And were are some fresh pic's ?

[cityslicker]

I'll take some pics when i get home.

[cityslicker]

[cityslicker]

TUB OF LOTS OF PARTS.


These gauges are in such good condition same as the new forks, I'll have to use them. Re do my paint scheme on em


And my baby waiting for all her new gear.... she's so patient.. not like my actual girl.

[cityslicker]

Sorry, here is the TUb

[shinyribs]

  "she's so patient.. not like my actual girl. "

Such is life!

You got all kind of good stuffAre those Procomp M/T's i see? Do you like em?

[cityslicker]

the 620 chain is in perfect condition, so are the gears, so I'm going to run that, I don't feel like spending the money on a new 530. I gotta save cash where I can. I'm glad I didn't get the fork seals yet, because the new ones are pristine. The new engine is in just wonderful condition, in fact everything accept the master cylinders are. those are shot. I guess I'll rebuild them, unless yinz know if I could use some off say an R1 or GSXR something new. I can't figure a reason why I couldn't.
i read up on doing the dual front Disc brakes, and They said I need a speedo colar off a cb550 so that it will fit inside the dic... can any of you corroborate that?
I got so many parts now I kinda don't know where to begin...
What should my next step be? swap the new forks onto the fram? That sounds good. think I'll do that... Then I can instal my new gators and headlight ears. then I'll start painting the new gauges. maybe pop that engine on the new frame., clean out the carbs.. I could hear a nice compression sound coming through the carbs as I spun the engine... thats refreshing.

[cityslicker]

They are pro comp EXTEEEEEEEEEEEEEEME MTs. get it right sucka.. I just got em in the mail yesterday. I'll keep you posted, but they are very nice in person.. pics don't do them justice. i am putting them on on thurs. After that I hope it snows buckets.

[shinyribs]

ooooh  xtreme mtS!!!   Excuse meI was considering those for my truck,but i rack up so many interstate towing miles i had to pass on them.I thought i recognized them.Youre making me jealous City

[TOOLS1]

You do not need the CB 500-550 speedometer drive. You can modify the CB 750 one, and use it. You cut the out side of the drive off where in curves down. Then JB weld it to the hub, using the axle to hold it in place. After the JB cures; drill a 1/8 inch hole through the speedometer drive gear, and into the hub about a 1/2 inch. Then install a 1/8 inch roll pin. Let it stick out about a 1/16 of an inch. It will work perfect.
TOOLS

[cityslicker]

BAM< tools strikes again. Thanks buddy

[cityslicker]

I actually got the pro comps over the BFG KM2s because they hold up better on roads. said about 80k out of a set,. I was on board.

[Piute]

 You building 2 bikes now ? have enough stuff there  clean it up lay it out and get some on that girl
 plenty to keep you busy fo-sho
  Had 35 Pro-Comp mudders on my jimmy went into everything miss that boy

[cityslicker]

I love the stance he got Man, did you have to re gear the difs to turn them 35s? what axles on the front of them old jimmys?

[Piute]

 Didn't do anything but cut out fire wall so I could turn,Washed it twice.
 I paid 800 bucks for it put about 2k more into engine and suspension (without a lift)over time.
AND ran the piss out of it was my fishing and winter beatter,Hella fun for 4years then got a 90 XLT to beat on and sold tire for 300 $ kept one(had 5) made a kick azz table (street lockers) Sold my boy to 1st person that came over with cash 60 bucks sold.To many toys

[cityslicker]

Tire Table?

[cityslicker]

Piute king of recycling.

[cityslicker]

I got the eingine in last night.... I have been sleeping on my build of late. Had to fix my car, my computer, and now my truck.... UUUGHHHH. but I'll have her on the road this season.

[rrgunslinger]

Know how u feel.

Harvey

On Mar 28, 2012 10:21 AM, "cityslicker [via Honda CB750&apos;S]" <[hidden email]> wrote:

I got the eingine in last night.... I have been sleeping on my build of late. Had to fix my car, my computer, and now my truck.... UUUGHHHH. but I'll have her on the road this season.

---

If you reply to this email, your message will be added to the discussion below:

http://honda-cb750-s.456789.n3.nabble.com/New-to-the-site-Will-need-alot-of-info-from-all-you-tp3220918p3864652.html

To start a new topic under Honda CB750'S, email [hidden email]
To unsubscribe from Honda CB750'S, click here.
NAML

[cityslicker]