MR. James_Black 1980 Honda cb750f PROJECTO :p

[Mr.James_Black]

Thanks a lot guys. I order them and I got them at home. They sent me 50mm.
So I got the tank and the pods. By this weekend I should be able to put them.

Quick Question

harley peanut tank 3.2

Do I need to line it before use or the liner is just to restore old rusty tanks?
Suggestions, Ideas...let me know before i install it.
:D
You guys rule!!

[Mr.James_Black]

nobody?  simple answer. thanks

[shinyribs]

Line your tank at your own discretion.Some do,some don't Some peel,some don't.I persoanlly dont see the need. Your Welcome.

[TOOLS1]

I wouldn't!
TOOLS

[rrgunslinger]

I lined mine with no problems. If not done right it will not take. If you don't have any leaks or major rust I would not worry about it. 

On Fri, May 25, 2012 at 12:21 PM, Mr.James_Black [via Honda CB750'S] <[hidden email]> wrote:

nobody?  simple answer. thanks

---

If you reply to this email, your message will be added to the discussion below:

http://honda-cb750-s.456789.n3.nabble.com/MR-James-Black-1980-Honda-cb750f-PROJECTO-p-tp3788082p4015533.html

To start a new topic under Honda CB750'S, email [hidden email]
To unsubscribe from Honda CB750'S, click here.
NAML

[Piute]

Mr.James_Black wrote

Thanks a lot guys. I order them and I got them at home. They sent me 50mm.
So I got the tank and the pods. By this weekend I should be able to put them.

Quick Question

harley peanut tank 3.2

Do I need to line it before use or the liner is just to restore old rusty tanks?
Suggestions, Ideas...let me know before i install it.
:D
You guys rule!!

                         3.2 X 40 =  120 ?  stoping for gas every 100 at least (most)
                          if passanger,would like that

[Lucky 1]

Why don't you take on the responsibility yourself.

Buy a workshop manual. Read.Learn. Get off of the device.
If it was me I would go to the DOHC forum.

[shinyribs]

Or you could continue hanging out with us where you are entirely welcome. There are knowledgeable DOHC here as well.

[Mr.James_Black]

So.. I took sometime yesterday and cleaned up the bike. I also murdered it out. Love the all black look.
I used Black Engine Spray paint (2000 degree). For the back fender I also use Undercoating on top of the engine spray.

This week....The tank should be welded. Then...........RIDE AND RIDE AND RIDE :D

[Mr.James_Black]

and to Lucky 1


Its people like you that I despise.
HEy you gain your knowledge by asking right?
So its my turn so get of the device and mind your own buisness.

[shinyribs]

I have seen some murdered out bikes,cars,trucks before...but that one is plum MURDERED OUT! Holy crap,that looks tuff!  Keep the updates coming,please.I'm loving this!

[TOOLS1]

Bike is looking good. Love the alien.
TOOLS

[Mr.James_Black]

Brothers n Sisters........The tank is welded :D
All I got left is put a new battery, find the 2 screws for the seat, install the air pods, give her a new coat of black paint and place the stickers. Ill be doing in this weekend :) Updates soon!!!!



Im a little concern about the location of the petcock. All I can think is about gas efficiency. I need to keep an eye and make sure the tank is always full. :?
Any suggestion before I put gas in it? Thanks Bro's :D

[shinyribs]

Hmmm,that stinks on the petcock. Any chance you can move it while your are still in the welding stage? Or have you painted it yet?

[Mr.James_Black]

Its all welded and done. I asked him if he can do it but mention something about been "pressed"

Any suggestions?

[shinyribs]

I dont have any ideas,other than welding that petcock shut and moving it/another one to a better spot. Sucks there is no easy solution to this.

[TOOLS1]

"Pressed" Just put a pipe plug in the petcock hole. Then drill a new hole, and weld a pipe bung/fitting over the new hole. Re-install the petcock. Paint to please, and your done.
TOOLS

[slownugly007]

What was welded on the tank? Was the actual tank welded up or was it welded to the frame? I'm confused?

[Mr.James_Black]

Tools. Thanks for the advise. I will talk to my welder and see if we can do this.

SlownUgly
It was welded to the the frame.

[TOOLS1]

"Welded to the frame?" You can't weld a gas tank to the frame!!! The vibrations will cause it to crack, and dump gas into your lap, and onto a hot engine. Please bolt it on!!.
TOOLS