Piute putt 1977 CB 750 F2

[shinyribs]

HAHAHA! You know,Tommy did say he didn't remember it having a cracked lens when he parked it in the shed...maybe it did get shot while it was just sitting around

[Piute]

                                                                 


                                               Ordered smoke / silver ends TANKS Mark


                                                                                          were's my 10mm.........
                                                                                          ..........Vetter ...1/2 "..?..

[Piute]

 


                    O.K. I ordered 10 crush washers with my S.S. lines ,
                    Should there be 1 on each side of the banjo
                                                     

                                                      piute putt n judose

[TOOLS1]

Piute wrote

O.K. I ordered 10 crush washers with my S.S. lines ,
                    Should there be 1 on each side of the banjo

Yes!
TOOLS

[Piute]

24681012141618-216I'm 6 shorti'm going to bedgood-night 1more

[Piute]

                                                         Bought this
                                                   CB650 SC Oil Cooler

                           Check CB650 SC Oil Cooler for CB750's by sgtslag

                                                   TANKS sgtslag Sir

              lost out on bidding on this by .50 cents I need to get better at bidding                    
                                       lower's sold 25.50 + 15.00shp.

[shinyribs]

Piute,you can make your own lowers man. You did a great job on your side covers.

[Piute]

,The 1's I need "Wind Jammer V " are the hardest to come by ,SO by getting stk. making molds,I can make to order ,Mine can't be looking stk. but still mount in same holes So for streangth and flow best to have stk. to start,Thanks for the confident in me and will do,have to have oil-cooler mounted for my custom  lowers.explain later during making
  Just finishing up the oil bagg side cover,You'll either like it or think not worth it,cause not much there.
     It's just a ring around the oil bagg, my 1off custom that will be noticed.

[TOOLS1]

That's the same oil cooler we are putting on my buddies bike. The oil lines, and two small fins hit the block. We are going to remove the oil lines, and tap to 1/4 inch pipe, and have braided stainless lines made. Also, you will need a 5/8 inch spacer. It just, so happens we are having some made up. Should I put, you down, for one?
TOOLS

[Piute]

                                 FILTER / OIL COOLER / SPEC. for 650sc N cb750 F2

http://www.bikebandit.com/houseofmotorcycles/1984-honda-night-hawk-650-cb650sc/o/m151719#sch400589
http://www.bikebandit.com/houseofmotorcycles/1977-honda-750-super-sport-cb750f/o/m151839#sch403072
 
                                               use Bike Bandits OEM spec.
                                             
    O.K. looking at both specs  84 650sc    side by side         with 77 750f
                     
                         main bolt   581221 650 smaller houseing    581110
                     valve check    581240       same                    581240
            spring valve check   581241       same                     581241
          pin spring setting      581242       same                     581242
                   bigg spring      581099       same                     581099
                             filter     581064       same                     581064

                                                    bigg"O" ring 89x4.5

          So what ya think can I just swap out the rear plate and remove ? spacer.
           need to see inside SC plate fo flow desgn
          this is cool learning alot all over this putter

  With all even the K being the same any switch should be easy for all Tanks again srg/ tools

[shinyribs]

Hey bud. Got your side boxes today. A little rough to be honest. Ill email you some pics tonight

[Piute]

            RUFFRuff
                   There fiberglass right
             have grinders do work
                       howw  RUFF is

[Piute]

   I  can't believe this ,Kinnda added up my $$$ ,about at the limit,last bits N peaces will Limit.

                                                        piute putt n judose

She will look like this for the most part ,Will put back together this week end IF I get Saturday off.
  After running real good then bagg it ,should have all parts painted by then June/July anniversary

[Piute]

                                               These lights hide A Lil to good

    Had A bike on the left of me(me in truck)I stoped red light ,He was trying to get in my lane I never seen his blinker from the side,When did he was trying/did make a right ,he had the same lights as these
    I know BIGG azz tail light way out of place,Some states Can't have smoke lenses,SO can ya have both? Thinking clear 3ways tail/blinker/brake N lic.light.

[Piute]

        SO the idea is to put side makers/blinkers front and rear (on order) frnt will go on ears,rear on cowl
   This should stop me from being pulled over /I'm old school and use hand signals alway.
                                                     (watch for finger too)

[Piute]

                                          These are On there way from the BAY
              Tryed the cat eye blinkers COOL but that stk. tail light STOP sign gotta go
            Check out state law no signal lights required,So these are for safety,side view

[shinyribs]

VA doesn't require turn signals either.I like hand signaling too,but they wont see that at night.Best to have some bright blinkers for night time

[Piute]

 opps Try this again

          My riding vest is very reflective even though it's H.D.works great,looking for good reflective riding gloves must me renforced ,reflective piping,long,"O" n not ov er 30 bucks if leather maybe bit more.
  Those bone heads aren't going to see me ,I'm to dark and my bike is blk,think dragg pipes

[shinyribs]

Drag pipes with fire shooting out of them! That'll get their attention!!

[Piute]

                              Lil propane and spark plugg